Modem Products


Home | Profile | Products | Prices |  Contact Us
SERIAL MODEM
OEM #7710

RS-232C COMPATIBLE 

33,600 Baud Modem and Group 3 Send/Receive FAX for full duplex operation over the public switched telephone network (PSTN)
 
  • Functionally and Electrically RS-232C Serial or TTL Compatible
  • Standard "AT" Command Set Including S Registers and Result Codes
  • Auto/Manual Answer Or Dial
  • Detects Busy, Ring, Dial Tone, Carrier
  • DTMF and Pulse Dial
  • Complete "&T" Testing Capability with Loop-back and Memory Test
  • Supports ECC: V.42 LAPM, MNP 2-4 and MNP 10 Error Correction. V.42 bis and MNP 5 Data Compression. MNP 10 EC™ Enhanced Cellular Performance.
  • Non-volatile RAM for User Phone Directory and Stored Operating Profiles

·  Data Rate:  Modem - all rates to 33,600 bps  FAX - up to 33,600 bps
·  Compatibility:  Modem - V.34, V.32 bis, V.32, V.22 bis,V.22, V.23, V.21, Bell 212A & Bell 103. Supports ECC: V.42 LAPM, MNP 2-4 and MNP 10 error correction. V.42 bis and MNP 5data compression. MNP 10 EC™ Enhanced Cellular Performance.  FAX - V.34, V.17, V.29, V.27 ter, and V.21channel 2. Supports T.30 protocol.
·  Operational Modes:  Full or Half Duplex, Auto Dial, Auto Answer, Auto Redial, Tone or Pulse. 
·  Internal Telephone Number Directory:  Supports four saved numbers of 35 characters each.
·  Dialing:  DTMF - in accordance with CCITTQ.23  Pulse - in accordance with EIA/TIA-496-A Blind - by command
·  Ringer Equivalence:  0.6B
·  Command Buffer:  40 Character
·  Host Interface:  DB-9 female right angle (EIA/TIA-232-E or10-pin header or TTL)
·  Telephone Interface:  RJ-11C line jack (only Tip & Ring required)
·  Command Set:  Full AT including ext commands, S registers, Result Codes
·  Size/Weight:  3.55 x 4.25 x 0.7” (90 x 108 x 17.8mm) 2.45 oz (69.4 gm)
·  Line Impedance:  600 ohms, ±10%
  • Power:  Off Hook:  5 volts ± 10% 165mA (7-24V with –REG Option)
        Idle: 145 mA  Sleep: 80 mA  -LED Option: 10 mA

 ENVIRONMENTAL SPECIFICATIONS

  • Operating Temperature: 0° C to +70° C (32° F to 158° F) 
  • Storage Temperature: -55° C to +125° C (-67° F to +257° F)
  • Relative Humidity: Up to 90% noncondensing, or wet bulb temperature to 35° C, whichever is less.
  • Extended Temp Version: -49° to 85° C, 0-90% RH noncondensing

Options
-LED
LED indicators. May be disconnected after setup to reduce power consumption.
-CID
Caller ID
     -LCS
Loop Current Sense – detects line in use.
     -CASE
Black plastic protective case 3.8” x 4.6” x .85”
     -EXT
Extended temperature from -40° to 85° C, 0-90% RH noncondensing.
     -REG
Allows 6-30V DC power source
Home | Profile | Products | Prices |  Contact Us
Copyright 1997-2008 Aprotek, Inc. All Rights Reserved
Oregon USA, Phone: 541-582-2120 Fax: 541-582-2149
E-mail: aprotek@aprotek.com